Buy Now. Pay With 
Learn More
Every car ›Volvo ›S80 ›2006 - 2016 ›2.0 D3 (Pre 2010)
Diesel · 2.0 litre · Maidstone, KentVolvo S80 2.0 D3 (Pre 2010) remap163 to 185 bhp with Stage 1 software. The figures, the parts and the other engines in this car, on one page.
A Stage 1 remap takes the Volvo S80 2.0 D3 (Pre 2010) from 163 to 185 bhp and from 340 to 450 Nm: 22 bhp and 110 Nm more, on standard hardware. Diesels gain most in torque, so the change shows as pull from low revs and less gear-changing under load, not just a higher peak figure. It is done in a visit at our Maidstone workshop and the original file is kept, so it can go back to standard.
Stage 1 on this engine
What the Volvo S80 2.0 D3 (Pre 2010) makes, standard and remapped
Standard is the factory figure. Stage 1 is the calibration we run on this engine, software only, nothing bolted on.
163→185
BHP · Power · +22
340→450
NM · Torque · +110
Stage 2 and Stage 3 figures, and the price for each, are in the calculator for this exact engine.Open the calculator →
Stage 1 powerStage 1 torque (dashed)Standard
Drawn from the quoted peaks: torque peaks at the quoted Nm, power is derived from it. A measured before-and-after graph comes with a dyno session.
In the shop
Parts that fit the Volvo S80 2.0 D3 (Pre 2010)
Listed for this engine, fitted here or shipped. Anything from this list can be added to a Stage 2 build.
Same car, other engines
Volvo S80 2006 - 2016: every engine we tune
1.6 D - 109HP109 → 136 bhp
1.6 D - 115HP115 → 140 bhp
2.0 D - 136HP136 → 172 bhp
2.0 D2 - 120HP120 → 180 bhp
2.0 D4 - 181HP181 → 230 bhp
2.0 D4 (Post 2010) - 163HP163 → 185 bhp
2.0 T - 203HP203 → 270 bhp
2.0 T5 - 240HP240 → 270 bhp
All Volvo S80 engines (102) · Every Volvo we tune (1377) · All makes
Fixed price
Ask about your Volvo S80 2.0 D3 (Pre 2010)
Registration and which stage. We come back with what it needs, what it makes and what it costs, usually the same day.
Questions
Volvo S80 2.0 D3 (Pre 2010) remap questions
How much power does a Stage 1 remap add to a Volvo S80 2.0 D3 (Pre 2010)?
22 bhp and 110 Nm. Standard is 163 bhp / 340 Nm; Stage 1 is 185 bhp / 450 Nm. That is a 13% power gain and 32% more torque.
How do I get a price for a Volvo S80 2.0 D3 (Pre 2010) remap?
Put the registration into the calculator and it prices Stage 1, 2 and 3 for this exact engine, or send the form on this page and we come back with a fixed price, usually the same day.
Is a Stage 1 remap safe for this engine?
Stage 1 stays inside what the standard turbo, injectors, clutch and cooling were built to take. The figures above are the calibration we run, not a maximum. The car is checked for stored faults before and after, and the original file is kept so it can go back on.
Will a remap affect the DPF or AdBlue on a Volvo S80 2.0 D3 (Pre 2010)?
No. A Stage 1 remap keeps every emissions system as the factory fitted it. We do not remove or disable the DPF, EGR or AdBlue system as part of a remap.
How long does it take, and can it be reversed?
A Stage 1 remap is done in a single visit, usually the same day. The original software is stored and can be restored on request.
Meet the team
The team behind every job
Technicians, calibrators and the front desk, all in Maidstone. No call centre and no subcontracting - the person who books you in is the person you can ask about the job.
Newsletter
Offers on parts and tuning, first
A short email now and then: new vehicle support, parts deals, open days. Nothing daily.